These 3-in-1 Swap Top Mister Micro Sprays give you 3 choices of spray patterns including a 360° Flat Fan Spray, a narrow Center Strip, and a 90° Half Circle spray pattern.
This 3-in-1 Swap Top Mister Micro Spray is ideal for watering small areas, atriums, shrubs, small trees, plants, flowers, shrubs, and trees along walkways, fences, driveways, and the perimeter of a house
Easy to interchange the spray patterns by sliding off the Yellow Swap Top, reversing it, then sliding it back onto the Red G-shaped Micro Spray Mister
The Red G-Shaped Micro Spray is ideal for roses as the 360° x 14 stream down spray keeps water off foliage and petals and waters up to a 4-ft diameter.
Slide the Yellow Swap top onto the Red G-Shaped Micro Spray and you will receive on one side, a 90° Fan Spray that is ideal for use in corners and tight areas and waters up to a 4 to 5-ft radius. If you reverse the Swap Top, you will receive a Narrow Center Strip on the other side that waters a spray width of 1-3-ft and is ideal for long narrow areas of landscaping.
When installed on top of our Mister Riser Assemblies (MLS-231), or any of our Micro Stake Assemblies (MLS-211, MLS-TAN, or MLS-BLA), this Micro Spray uses only 9-15 GPH, depending on your water pressure and the amount of Micro Sprays used. (See Maximum Runs below for more information).
(4 Misters Per Bag)
(Made in the USA)
RECOMMENDATIONS & LIMITATIONS
When installing any irrigation system, it is important to be aware of manufacturer recommendations and potential system limitations. Please be aware of the following:
INSTALL IN THIS ORDER:
Order of installation is critical for proper system function. This is the order in which parts should be installed, starting from an outdoor water faucet.
1) Check your outdoor faucet to make sure there is an attached or built in Brass Anti-Siphon Vacuum Breaker that’s designed to prevent the backflow of fluids back into the potable/drinking water system.
2) Metal "Y" Fitting is suggested so you can still attach your garden hose.
3) The Electronic Mister Timer (MLWT-1ZONE, MLWT-TWOZONE, or MLWT-EGG)
4) Pressure Regulator: When using our Micro Sprays with a water pressure over 50 PSI, use our 40 PSI Pressure Regulator (MLA-40PR), and when using Drippers, we highly suggest using our 25 PSI Regulator (MLD-25PR)
5) 150 Mesh Filter (MLFF-41),is suggested for Drippers or when using our products with "well" water.
6) 1/2-in Poly Faucet Fitting (MLF-33), which connects to the 1/2-in Poly Tubing OR the 1/4-in Faucet Adapter (MLA-FAS), which connects to the 1/4-in Vinyl tubing.
For more information, please download our Installation Guide (PDF) with more information.
MAXIMUM RUNS
Run up to 300 feet of our 1/2-in Poly Tubing installing up to 40 of our Micro Spray Stake Assemblies (MLS-211, MLS-TAN, MLS-BLA, or our Miser Risers (MLS-231).
When installed on top of any of our Landscape Micro Spray Stake Assemblies (MLS-211, MLS-TAN, or MLS-BLA), or our Mister Riser (MLS-231), this Micro Spray will only use 9 GPH up to 15 GPH depending on your water pressure and total amount of Micro Sprays installed. The following test results are using the Maximum Run of 300 feet of ½” Poly Tubing with a water pressure of 40 to 50 PSI. The Micro Sprays at the beginning of the run will spray a higher GPH and they will use a lower GPH down at the end of the run. The lower the total amount of Micro Sprays used on a run, the higher the GPH.
When using 40 to 35 Landscape Micro Spray Stake Assemblies, the Micro Sprays will use approximately 12 GPH at the beginning of the run down to 9 GPH at the end of the run.
When using up to 30 Landscape Micro Spray Stake Assemblies, the Micro Sprays will use approximately 12 GPH at the beginning of the run down to 11 GPH at the end of the run.
When using 25 to 20 Landscape Micro Spray Stake Assemblies, the Micro Sprays will use approximately 14 GPH at the beginning of the run down to 13 GPH at the end of the run.
When using up to 15 Landscape Micro Spray Stake Assemblies, the Micro Sprays will use approximately 15 GPH.
When winterizing your system, before the first frost, completely remove the Timer and batteries and store inside. You may also use our Winterizing Plug (MLA-WHTPLUG) to seal off your system. After removing the Timer and Hose Fitting from the faucet, simply thread the Winterizing Plug into the Hose Fitting to seal off the line.
If you would like to run drippers with our Micro Spray Stake Assemblies, you can run up to 300 feet of our 1/2-in Poly Tubing, installing up to 30 of the Micro Spray Stake Assemblies (MLS-211, MLS-TAN, MLS-BLA), and fewer than 10 drippers off one faucet. If you want to run more than 10 drippers and you already have 30 Micro Spray Stake Assemblies installed, then you would need to replace each 10 GPH Micro Spray Stake assemblies with one of the following choices in drippers: 20 0.5 GPH drippers (MLD-.5PC), 10 1 GPH drippers (MLD-PC1), or 5 2 GPH drippers (MLD-2PC).
Attach up to 6 of our Micro Spray Kits (MLK-81, MLK-82T, or MLK-LG) off one faucet
Minimum operating pressure for Micro Spray Stake Assemblies: 15 PSI
Maximum operating pressure for Micro Spray Stake Assemblies: 50 PSI
